Router instellen voor telenet [Archief]

Snoepy

30 July 2005, 00:51

Welkom op het forum.

Dit is je eerste post zie ik net.
Wens je veel succes op het (y) forum.

mss helpt je dit een beetje verder.

Als het om deze gaat.

http://www.usr.com/support/8200/8200-ug/images/8200%20router%20front.gif
Kijk eerst of je lampjes werken

POWER
Green - Lighted: Operating normally
Red - Lighted: An error has occurred

WAN
Green - Lighted: WAN connected
Green - Blinking: Receiving and transmitting WAN data

USB1
and
USB2
Green - Lighted: USB storage device connected
Green - Blinking: Receiving and transmitting data
Off: No connection

1394
Green - Lighted: FireWire storage device connected
Green - Blinking: Receiving and transmitting data
Off: No connection

LAN 1-4
Green - Lighted: 100 Mbps LAN link
Green - Blinking: Receiving and transmitting data at 100 Mbps
Amber - Lighted: 10 Mbps LAN link
Amber - Blinking: Receiving and transmitting data at 10 Mbps

PS. Reset je modem van telenet eens door even de stekker uit te trekken en na een sec. of 10 weer in te steken.

Doe dit ook met je router eens door ergens op een reset knopje te duwen. mss achteraan of zo.

Als dat goed is.

Select your Internet Connection type and click Next.

http://www.usr.com/support/8200/8200-ug/images/network-conn-internetconn1.jpg

Enter the appropriate information for your Internet Connection and follow the on-screen instructions. When you are finished, you should have a secure connection to the Internet.

Je kiest dan voor:

External Cable Modem

JE KAN DE VOLGENDE TEST DOEN OM TE ZIEN OF JE INTERNET WERKT

Troubleshooting Ping Procedure

If at any time during the ping procedure you do not receive a return message for a successful ping, this means that the address you are pinging has been changed and is causing a conflict. Check the address in the configuration utility and make any necessary corrections using the console mode. After you have made the corrections, continue with the ping procedure.

Click Windows Start and then click Run. In the Run dialog box, Windows 95, 98, and Me users should type command and click OK. Windows NT, 2000, and XP users should type cmd and click OK.
Type Ping 127.0.0.1. This is your local host address and this will ensure that the TCP/IP protocol is installed and functioning properly. If you cannot complete this ping, disconnect the router and then repeat the installation procedure.
Type Ping followed by your IP address. This will ensure that your PC is responding to requests. If you cannot complete this ping, make sure all the cables are properly connected and that all the correct drivers are installed.
Type Ping followed by your gateway address to check the communication with your gateway. The default gateway address is 192.168.1.1 This will ensure that you can connect to other machines and can get to the USR8200 Firewall/VPN/NAS. If you can establish communication with the USR8200 Firewall/VPN/NAS, you can access the Administration page and configure the settings. If you cannot complete this ping, make sure the power cord of the USR8200 Firewall/VPN/NAS is plugged in and that it is properly connected to your PC or Macintosh.
Type Ping followed by the outside Internet address of your USR8200 Firewall/VPN/NAS. This is the address that is provided either by your ISP or by the outside LAN. This procedure will ensure that your USR8200 Firewall/VPN/NAS is functioning properly and allowing traffic to pass through.
Type Ping followed by your known DNS server address. This will allow you to resolve valid Internet host names to IP addresses and to verify that you can access the Internet.
sup.:http://www.usr.com/support/s-main-menu.asp

Veel succes