Weergegeven resultaten: 1 t/m 3 van 3
  1. #1
    Beginner  
    Geregistreerd
    13 May 2005
    Locatie
    The Sea
    Berichten
    7
    Bedankjes
    0
    Bedankt
    0 keer in 0 posts

    Router instellen voor telenet

    Goedenavond,

    Het probleem van mijn vriend is als volgt :

    Heeft een US-Robotics Router die een desktop en een laptop zou moeten
    voorzien van een internetaansluiting (Telenet). Als ik echter de modem van
    telenet verbind met de router en die daarna verbind met de desktop, krijg ik geen verbinding met het internet. Heeft dit te maken met het IP adres?

    In mijn router staat de DHCP nochtans ingeschakeld. Welke keuze van verbinding dien ik aan te vinken in de basisconfiguratie? PoPP of zoiets?

    Ikzelf heb Skynet en daar was het simpel mijn login invoeren in de Router (Philips) om de verbinding tot stand te brengen.

    Dank voor de hulp op voorhand.

    Hilaire deTipelaire
    Alleen Bomen en Bergen komen elkaar niet tegen!!!



  2. #2
    Gevorderd  
    Geregistreerd
    14 May 2005
    Berichten
    117
    Bedankjes
    10
    Bedankt
    11 keer in 9 posts

    Re: Router instellen voor telenet

    Welkom op het forum.

    Dit is je eerste post zie ik net.
    Wens je veel succes op het forum.

    mss helpt je dit een beetje verder.


    Als het om deze gaat.



    Kijk eerst of je lampjes werken


    POWER
    Green - Lighted: Operating normally
    Red - Lighted: An error has occurred

    WAN
    Green - Lighted: WAN connected
    Green - Blinking: Receiving and transmitting WAN data

    USB1
    and
    USB2
    Green - Lighted: USB storage device connected
    Green - Blinking: Receiving and transmitting data
    Off: No connection

    1394
    Green - Lighted: FireWire storage device connected
    Green - Blinking: Receiving and transmitting data
    Off: No connection

    LAN 1-4
    Green - Lighted: 100 Mbps LAN link
    Green - Blinking: Receiving and transmitting data at 100 Mbps
    Amber - Lighted: 10 Mbps LAN link
    Amber - Blinking: Receiving and transmitting data at 10 Mbps


    PS. Reset je modem van telenet eens door even de stekker uit te trekken en na een sec. of 10 weer in te steken.

    Doe dit ook met je router eens door ergens op een reset knopje te duwen. mss achteraan of zo.

    Als dat goed is.


    Select your Internet Connection type and click Next.



    Enter the appropriate information for your Internet Connection and follow the on-screen instructions. When you are finished, you should have a secure connection to the Internet.

    Je kiest dan voor:

    External Cable Modem


    JE KAN DE VOLGENDE TEST DOEN OM TE ZIEN OF JE INTERNET WERKT

    Troubleshooting Ping Procedure

    If at any time during the ping procedure you do not receive a return message for a successful ping, this means that the address you are pinging has been changed and is causing a conflict. Check the address in the configuration utility and make any necessary corrections using the console mode. After you have made the corrections, continue with the ping procedure.
    1. Click Windows Start and then click Run. In the Run dialog box, Windows 95, 98, and Me users should type command and click OK. Windows NT, 2000, and XP users should type cmd and click OK.
    2. Type Ping 127.0.0.1. This is your local host address and this will ensure that the TCP/IP protocol is installed and functioning properly. If you cannot complete this ping, disconnect the router and then repeat the installation procedure.
    3. Type Ping followed by your IP address. This will ensure that your PC is responding to requests. If you cannot complete this ping, make sure all the cables are properly connected and that all the correct drivers are installed.
    4. Type Ping followed by your gateway address to check the communication with your gateway. The default gateway address is 192.168.1.1 This will ensure that you can connect to other machines and can get to the USR8200 Firewall/VPN/NAS. If you can establish communication with the USR8200 Firewall/VPN/NAS, you can access the Administration page and configure the settings. If you cannot complete this ping, make sure the power cord of the USR8200 Firewall/VPN/NAS is plugged in and that it is properly connected to your PC or Macintosh.
    5. Type Ping followed by the outside Internet address of your USR8200 Firewall/VPN/NAS. This is the address that is provided either by your ISP or by the outside LAN. This procedure will ensure that your USR8200 Firewall/VPN/NAS is functioning properly and allowing traffic to pass through.
    6. Type Ping followed by your known DNS server address. This will allow you to resolve valid Internet host names to IP addresses and to verify that you can access the Internet.
    sup.:http://www.usr.com/support/s-main-menu.asp

    Veel succes
    Laatst gewijzigd door Snoepy; 30 July 2005 om 01:43

  3. #3
    Beginner  
    Geregistreerd
    13 May 2005
    Locatie
    The Sea
    Berichten
    7
    Bedankjes
    0
    Bedankt
    0 keer in 0 posts

    Re: Router instellen voor telenet

    Thx very much,
    Daarmee zal ik het wel klaarspelen.

    Hilaire de Tipelaire.

    Alleen Bomen en Bergen komen elkaar niet tegen!!!



Discussie informatie

Users Browsing this Thread

Momenteel bekijken 1 gebruikers deze discussie. (0 leden en 1 gasten)

Soortgelijke discussies

  1. Telenet Accountinstellingen voor Mozilla?
    Door samsu in forum Internet
    Reacties: 8
    Laatste bericht: 22 January 2006, 23:37
  2. router op router aansluiten
    Door Wouter in forum Netwerken en internetproviders
    Reacties: 9
    Laatste bericht: 14 October 2005, 07:26
  3. turbopakket voor telenet
    Door kwakkwak in forum Netwerken en internetproviders
    Reacties: 17
    Laatste bericht: 10 October 2005, 21:12

Favorieten/bladwijzers

Favorieten/bladwijzers

Regels voor berichten

  • Je mag geen nieuwe discussies starten
  • Je mag niet reageren op berichten
  • Je mag geen bijlagen versturen
  • Je mag niet je berichten bewerken
  •